Aerospace and defense manufacturing insurance is built around products liability for parts that fly or go into defense systems, the insurance terms your customers pass down in their contracts, and coverage for the precision equipment and customer-owned material on your floor. How your liability form treats aircraft products usually shapes the rest of the program.
Why aircraft parts change the liability placement
The first underwriting question is whether your parts are installed on aircraft at all, and if so, whether they are flight-critical. The answer decides which market writes your liability. Many standard general liability forms exclude or restrict aircraft products, and a carrier that learns partway through the policy term that a shop makes aircraft components will often add that exclusion by endorsement.
That is why a shop making aircraft parts often needs aviation products liability placed with a specialty aviation market. Those underwriters work from the part itself: what it is, which system it goes into, and what happens if it fails. A landing gear component and an interior trim bracket are both aircraft products on many forms, but they are underwritten very differently.
Do not assume the answer from the size or simplicity of the part. Ask your agent to show you, on the form you actually have, how aircraft products and completed operations are treated and whether grounding is addressed. If the wording restricts aircraft products and you are shipping them, the policy may not be carrying the exposure you think it is. Our comparison of products liability and general liability for manufacturers explains the underlying coverage, so this page stays with the aviation wrinkle.
Grounding liability in plain words
Grounding liability addresses a loss that involves no crash and no injury: aircraft taken out of service because a part is suspected of being defective. When an operator or an authority grounds aircraft over a suspected defect, the owners lose the use of those aircraft, and they look to the supply chain for that loss.
Standard general liability is usually built around bodily injury and physical damage, so loss of use of aircraft that were never damaged tends to fall outside it. Grounding coverage is commonly part of aviation products forms for that reason. The details vary by form. How grounding is defined, what has to trigger it, whether it carries its own limit, and how it interacts with the products limit all depend on the wording.
For a lower-tier supplier, the practical point is that a grounding claim can reach a shop whose part turns out to be sound. The suspicion alone can start the loss. Ask how your form responds in that case.
How contract terms flow down to your shop
The insurance terms you are asked to meet were usually written by someone several levels above you. A prime contractor sets insurance requirements in its contracts, its upper-tier suppliers repeat them in their own purchase orders, and the terms arrive at your shop as conditions of the order. They commonly include required limits, additional insured status for the customer, a waiver of subrogation, and an indemnity clause.
Read those terms before you quote the job, not after you win it. Accepting a purchase order usually means accepting its terms, and a promise your policy does not back is a promise you carry yourself. Additional insured status has to be granted by endorsement, and the wording of that endorsement decides how far it reaches for products that have left your shop. Our guide to additional insured status for manufacturers covers how those endorsements work, and the article on what manufacturing customers require walks through the common contract terms.
Pay particular attention to the indemnity language. Some clauses ask you to answer for losses well beyond your own fault, and liability coverage for contractually assumed obligations is often limited by the form. Send the terms to your agent and, where the indemnity is broad, to your attorney.
The prime contractor
Sets the insurance terms in the contract
Sizes them to its own exposure
Upper-tier suppliers
Pass those terms down with their purchase orders
Often add terms of their own
Your shop
Agrees to limits, additional insured status, and indemnity
Does so when it accepts the order
Your insurance program
Has to match what you signed
Including how aircraft products are treated
Customer-furnished and government-furnished material
Material and tooling you do not own is usually your responsibility while it sits in your shop, and it is often worth far more than the machining you add to it. Aerospace customers commonly furnish forgings, castings, and dedicated fixtures, and defense programs may route government-owned material and tooling through the supply chain to your floor.
Many general liability forms restrict coverage for property in your care, custody, or control, so a forging scrapped by a programming error or lost in a fire may not be a liability claim the policy pays. The usual answer is property-of-others coverage on your property form or a bailee-type extension, with a limit set against the highest value you hold at any given time. Whether damage from your own workmanship is included depends on the wording, and many forms treat it narrowly.
Ask your customer for values in writing, check what the purchase order says about risk of loss, and confirm the valuation basis with your agent. The same questions come up with customer-owned tooling generally, which our article on tool and die shop insurance covers in more depth.
Real-World Scenario: A machine shop receives a pallet of customer-furnished forgings for a structural aircraft fitting. A fixture offset is entered wrong on the night shift, and several forgings are cut undersize before inspection catches it. Nobody is hurt and nothing else is damaged. The customer bills the shop for the forgings and the schedule delay. The owner turns to the general liability policy and learns that property in the shop’s care is restricted there, and that the property-of-others limit on the property form was set years earlier for much cheaper bar stock.
Non-conforming parts and paperwork errors
A part that is out of tolerance, or a certification that turns out to be wrong, often causes a purely financial loss, and that is usually an errors and omissions question instead of a general liability claim. Aerospace work runs on documentation: material certifications, process records, inspection reports, and the certificate of conformance that ships with the lot. If any of it is wrong, your customer may have to tear down assemblies, re-inspect, and re-qualify, with no injury and no physical damage anywhere.
General liability forms are commonly triggered by bodily injury or property damage, and they often exclude the cost of repairing or replacing your own work. Manufacturers errors and omissions is the coverage designed around the customer’s financial loss from a product that does not meet specification, subject to its own wording and exclusions. Our article on professional liability for machine shops explains where that line usually falls. If a carrier offers it to your shop, ask how it treats paperwork and certification errors specifically.
Machines, inspection equipment, and downtime
The property side of an aerospace shop is concentrated in a small number of very capable machines and the equipment that proves the parts are good. Multi-axis machining centers, coordinate measuring machines, and other inspection equipment carry high values, and standard property forms often do not respond when the cause of loss is mechanical or electrical breakdown. Our machine and equipment coverage page explains how that gap is commonly filled.
Lead time is the larger problem. A replacement machine may take a long while to arrive, and after it is installed, a customer may need the process qualified again before you can ship. Your income loss can run well past the physical repair, so the restoration period and any extended period on your business income coverage deserve a close read. The article on business interruption for manufacturers covers how that coverage is usually structured.
Outside processing, export controls, and data
Parts that leave your building for special processes are still your parts in your customer’s eyes. Heat treating, coatings, and non-destructive testing are commonly sent to outside processors, and your purchase order from the customer usually holds you responsible for the finished part regardless of who performed each step.
That raises several insurance questions. Property coverage for parts away from your premises and in transit is often limited unless it is specifically arranged. If a processor damages a lot, your recovery depends on its insurance and on the terms you agreed with it, and many processors limit their liability in their own paperwork. Ask processors for certificates of insurance, read their terms, and tell your agent which work goes out and what it is worth.
Defense work adds subjects of its own. Export-control registration is a separate topic from insurance; we cover it in our guide to export-control registration for machine shops, and the federal regulation section on registration of manufacturers and exporters of defense articles is published at the eCFR. Cyber coverage is also a separate policy, and it is worth asking about given the drawings and technical data your customers expect you to protect.
Limits and what an underwriter will ask
Contract limits, more than your own judgment of the exposure, usually drive how much liability limit an aerospace supplier buys. When the limit in a purchase order is higher than your primary policy provides, an umbrella or excess policy is the usual way to reach it. Confirm that the excess layer sits over the policy that actually carries your aircraft products, because an umbrella written over a general liability form with an aircraft exclusion commonly follows that exclusion.
Underwriters in this class ask specific questions, and thorough answers tend to produce better terms. Expect to describe:
- Which parts you make and which platforms they go on
- Whether any part is flight-critical, and how you know
- The share of your sales that is aerospace or defense
- Your quality system, including quality certifications, lot traceability, and record retention
- The contract terms you sign, including indemnity and additional insured requirements
- Your loss history, including any customer complaints or returns that never became claims
Gather the drawings list, sample purchase order terms, and a description of your inspection process before the submission goes out. When you are ready for us to review your program against your contracts, request a quote and tell us what you make and who you make it for.