Coverage Explained

Electronic Component Manufacturing Insurance, Explained

A machinist in safety glasses and ear defenders working a machine control panel while holding a laptop

Electronic component manufacturing insurance centers on products liability for parts built into other companies’ products, errors and omissions for parts that fail to perform, recall exposure, and property coverage for sensitive production equipment and stock. Which of those carries the most weight depends on where your components end up and who answers for the design.

Where the component ends up

End use drives the exposure more than the part itself does. A board, connector, cable or harness assembly, sensor, or power supply is a small piece of someone else’s product, and what it costs you to build says very little about what a failure can cost. The same connector carries a different exposure in a desk lamp, a vehicle, a medical device, and an industrial control panel. For device makers themselves, see medical device manufacturer insurance.

That is why an underwriter usually asks about end use before anything else. Consumer products raise the question of how many units are in the field and who is using them. Vehicle and medical work raise the severity of a single failure. Industrial controls raise the cost of a stopped process at a customer’s plant. A plant that sells into several of these markets should expect to break its sales down by each, because some carriers decline or exclude certain end markets outright and others specialize in them.

Many component makers do not know every final application, especially when they sell through distributors. Say so on the application and describe what you do know. An end use that surfaces for the first time during a claim is a harder conversation than a disclosed unknown. Our page on manufacturing insurance shows how we frame the wider program around that question.

Where the part ends up

Consumer, vehicle, medical, or industrial end use
Sets the size of the exposure

Someone is hurt or property burns

Overheating, fire, or shock traced to the part
Products liability and completed operations

The part does not perform

A financial loss with no injury
Errors and omissions, depending on the wording

The part has to come back

Your own recall expense
The customer’s recall claim against you

How an electronic component’s end use and failure mode point to different coverages. Forms vary, so the policy wording decides. No figures are shown.

When a failed component injures someone or starts a fire

Bodily injury and property damage from a failed component are usually a products liability matter. A power supply that overheats, a harness that shorts and starts a fire, or an assembly that delivers a shock is the kind of claim the products and completed operations part of a general liability policy is commonly written to address.

The component maker is rarely the only defendant. The injured person usually pursues the brand on the finished product, and that company or its insurer then looks upstream to whoever supplied the part. Your policy has to respond to a claim that reaches you secondhand, sometimes long after the part shipped, so keep policy records and lot records for as long as the parts are in service.

Read the products section for exclusions tied to end markets, since some forms remove certain uses by endorsement, and check whether sales outside the country are within the coverage territory. Our article on products liability versus general liability for manufacturers explains how the pieces fit, and higher limits requested by a large customer usually come from an umbrella above the primary policy.

When the part simply does not work

The more common loss in this trade involves no injury at all. A lot of boards passes your test and fails intermittently in the field. A connector does not hold its rating. Nobody is hurt and nothing burns, but your customer has rework, field service calls, and perhaps a stopped line, and it sends you the bill.

General liability often does not respond to that kind of pure financial loss. The form is built around bodily injury and property damage, and many versions carry exclusions aimed at the cost of repairing or replacing your own product and at products that fail to meet a promised level of performance. Whether any part of a given claim finds coverage depends on the facts and the wording, so treat a general liability policy as an uncertain answer here.

This is the errors and omissions question. Manufacturers errors and omissions coverage is commonly written to respond to a customer’s financial loss arising from a product that does not perform as intended, subject to its own definitions and exclusions. These forms are usually claims-made, and they differ a good deal from carrier to carrier. Our explainer on manufacturers errors and omissions covers the mechanics.

Real-World Scenario: A contract assembler builds control boards for an equipment maker. A reel of capacitors from a distributor turns out to be out of specification, and the boards pass functional test before they begin failing in the field. Nobody is injured. The equipment maker sends technicians to swap boards at its customers’ sites and sends the assembler a claim for the labor, the freight, and the replacement units. The assembler turns to its general liability carrier and learns that the claim describes a financial loss, not injury or damage, and that the answer depends on a coverage it had never been asked to consider.

When a component has to come back out

Recall is a separate exposure from liability, and a component maker meets it in a different way than a brand owner does. Getting a component back usually means opening finished products: locating affected units, shipping them, removing and replacing the part, and retesting. The part may be cheap, and the labor around it is not.

Recall coverage comes in different shapes. Some forms address your own recall expense, meaning the costs you incur to withdraw your product. Others can be written to respond when a customer recalls its finished product because of your component and claims those costs from you. A component maker’s real exposure is often the second kind, so ask which is on the quote. Our product recall page describes the coverage, and the article on product recall versus product liability explains why a liability policy usually leaves recall expense out.

Where a component goes into a consumer product, the Consumer Product Safety Commission publishes guidance for businesses on the duty to report. Whether and how it applies to your plant is a question for counsel.

Your design or your customer’s design

Design responsibility decides who answers for what when a part fails. A contract assembler building to a customer’s drawings and bill of materials generally answers for workmanship: placement, soldering, handling, testing, and whether the parts used matched what the customer specified. A company that designs its own sensor or power supply answers for the design as well, and underwriters commonly treat that as a heavier exposure.

The line blurs more often than owners expect. Suggesting an alternate part during a shortage, adjusting a layout for manufacturability, or writing the test procedure can each move some design responsibility onto you. Tell the underwriter where that happens, and keep the customer’s written approval for every substitution.

Contracts then move the risk around again. Supply agreements commonly include indemnity clauses, warranty terms that run past your own, required limits, and requests to name the customer as an additional insured. Each of those should be checked against the policy before you sign, since an indemnity you agree to is not automatically an indemnity your carrier will fund. Our guide to additional insured requests for manufacturers walks through the endorsements involved.

The plant, the equipment, and downtime

The property side of an electronics plant is concentrated in equipment that is costly, sensitive, and slow to replace. Placement machines, reflow ovens, inspection and test equipment, and clean or static-controlled rooms should be scheduled at values that reflect current replacement, and the property coverage form should be read for how it treats electronic equipment and smoke or contamination damage.

Breakdown is its own question. A standard property form often does not respond to mechanical failure, electrical arcing, or a power-quality event that damages a machine from the inside, and machine and equipment coverage is commonly where that is addressed.

Stock deserves a careful count. Reels and trays of components hold a great deal of value in little space, and customer-supplied components in your care may be treated differently from your own stock. Ask how property of others is covered and on what valuation basis.

Lead time is what makes downtime expensive. A replacement machine may take a long while to arrive, install, and qualify, so the business income part of the program should be measured against that reality. Our article on business interruption for manufacturers covers how that coverage is set. Where production systems are networked, ask about cyber coverage as well. It is a separate policy, and property and liability forms often limit or exclude that kind of event.

Purchased parts and the supply chain

A component maker carries its suppliers’ quality into its own product. Counterfeit, remarked, or out-of-specification parts from a distributor can pass incoming inspection and fail later, and your customer will usually hold you responsible first.

Whether your supplier’s coverage stands behind those parts is an open question in most cases. It depends on what the purchase terms say, whether the supplier carries meaningful limits, where the supplier is located, and whether its insurer can practically be reached. Buying from authorized channels, keeping certificates and lot traceability, and asking key suppliers for evidence of insurance all help. Underwriters commonly ask about each of them.

What an underwriter asks

An underwriter wants to understand end uses, design responsibility, and controls before quoting. Expect questions on these points:

  • End uses: sales broken out by market, and any applications you decline.
  • Design responsibility: your own designs versus building to a customer’s documentation.
  • Testing and traceability: inspection steps, test coverage, lot and date code tracking, and record retention.
  • Contract terms: indemnity, warranty, required limits, and additional insured requests.
  • Export sales: where products ship and where claims could be brought.
  • Loss history: claims, returns, and field failures, including those you paid yourself.

A clear submission tends to get better attention from the specialty markets that write this class. If you want us to review your program, send us your details: what you build, where it ends up, who owns the design, and what your customers’ contracts ask of you.

The bottom line

An electronic component maker should build its program around where the parts end up and how they can fail, because injury, non-performance, and recall usually point to different coverages, and the policy wording decides what each of them does.

Frequently asked questions

What insurance does an electronic component manufacturer need?

Most electronic component manufacturers start with general liability that includes products and completed operations, property coverage for equipment and stock, and workers compensation. Many then add errors and omissions for parts that fail without injuring anyone, recall coverage, equipment breakdown, and an umbrella. The right mix depends on where your components end up and what your contracts say, and the policy wording decides what each form does.

Does general liability cover a component that fails without hurting anyone?

No, not in most cases. General liability is built around bodily injury and property damage, and a component that simply does not perform usually produces a financial loss for your customer instead. Many forms also carry exclusions aimed at your own product and at products that fall short of a promised level of performance. Errors and omissions coverage is usually where that claim is tested, and the wording decides.

Do contract electronics assemblers need errors and omissions?

Yes, in many cases it is worth reviewing, even when the design belongs to your customer. An assembler still answers for workmanship, soldering, component substitution, and testing, and a mistake in any of those can leave a customer with a financial loss and no injury. Whether the coverage fits depends on your contracts, your end markets, and how a given form defines the work it applies to.

Who pays if my component causes a customer’s recall?

It depends on the contract and on which coverage you carry. Your customer will usually look to you for its recall costs, and many general liability forms exclude recall expense. Some recall policies address only your own costs, while others can be written to respond to a customer’s claim against you. Ask which version you have, because the difference rarely shows until a claim arrives.

Is my test and placement equipment covered for breakdown?

No, not automatically. A standard property form is usually built around causes such as fire, wind, and theft, and it often does not respond to mechanical failure, electrical arcing, or a power surge inside a machine. Equipment breakdown coverage is commonly added by endorsement or written separately for that purpose. Ask how your form treats electronic equipment, power-quality events, and the downtime that follows.

Does it matter what product my component goes into?

Yes. End use is usually the first thing an underwriter asks about, because the same connector or board carries a very different exposure in a toy, a vehicle, a medical device, or an industrial control. It affects which carriers will consider the account, how products liability is written, and whether exclusions for certain end markets appear on the form. Describe your end uses accurately.

About the author

Nate Jones, CPCU

Nate Jones, CPCU, is the founder of Wexford Insurance and Machine Guard Insurance, a specialty insurance agency placing machine shop and manufacturer coverage in 48 states across a 20-carrier specialty panel. He places products liability, errors and omissions, recall, and property programs for component makers and contract assemblers, so he works through end use, design responsibility, and contract terms with the owner before a submission goes out. Connect via the Machine Guard Insurance quote form or call 317-942-0549.

Insure your shop or plant with a CPCU-led agency

Tell us what you machine or make — a job shop, a product manufacturer, or both — and we will market it to carriers that write the class.